GATE 2026 ME question paper with solutions
All 65 questions of the official GATE 2026 · Mechanical Engineering · IIT Guwahati paper, each with the official answer and a worked solution.
Questions
General Aptitude · 10
- Q1 · 1 mark‘The team ________ more than 300 runs in 20 overs ____________ rains. However, some players needed to improve their…
- Q2 · 1 markIf a positive real x satisfies the following equation 2 x + 2 x = 48, then the value of x is ____________
- Q3 · 1 markThe next figure (indicated by ‘?’) in the sequence is
- Q4 · 1 mark‘All the mangoes in the basket are good.’ If the above statement is false, then which one of the following statements…
- Q5 · 1 markConsider the following statements about four numbers: (S1) The average of the four numbers is 25 (S2) Each number is…
- Q6 · 2 marks‘People are crowding around \_\_\_\_\_ pit into which \_\_\_\_\_ elephant has fallen. I have never seen an elephant…
- Q7 · 2 marksThe table lists the unit selling price of five products P, Q, R, S, and T. On a particular day, 250 items were sold…
- Q8 · 2 marksConsider a string P of length l that is laid out as a straight-line segment. Another string K is laid out as a…
- Q9 · 2 marksThe Roman senator Meritorius, his brother, his son, and his daughter have varying oratory skill levels. They are…
- Q10 · 2 marksWhich one of the patterns labelled P, Q, R, and S is used to generate the following figure?
Engineering Mathematics · 9
- Q11 · 1 markDomain A is bounded by curve x2 = 4y, ordinate x = 2, and x axis. The value of A y dxdy is
- Q12 · 1 markLet be a scalar function. Then, is
- Q13 · 1 markThe order and degree of the following differential equation are m and n, respectively. 3 / x3 + 2 / y2 / x + ( 2 / x2…
- Q14 · 1 markNewton-Raphson method for solving algebraic equations is based on
- Q15 · 1 markThe exact solution of 04 dx/1+x is represented as n. If m represents numerically evaluated value of the above integral…
- Q36 · 2 marksIf w = e z = e (x + iy), where i = -1, then which one of the following statements is correct?
- Q37 · 2 marksConsider the following differential equation y/ x = 3 y/ t + y If y(x, 0) = 10e-2x, then the solution of the…
- Q38 · 2 marksLet f(t) be a function of t defined for all positive values of t. The Laplace transform of f(t) denoted by Lf(t) = 0…
- Q39 · 2 marksA student council of 10 members consists of two students from engineering school, three students from science school…
Engineering Mechanics · 4
- Q16 · 1 markA horizontal disk has a radial frictionless slot in which a small block is confined to slide. The disk turns…
- Q41 · 2 marksTwo structural members are connected by a hinge and they are externally loaded as shown in the figure below. A and B…
- Q48 · 2 marksA block of 50 kg mass is on an inclined plane. The block is connected to another hanging mass M by an inextensible…
- Q50 · 2 marksA rigid slender bar, AB, is sliding against two mutually perpendicular frictionless walls, as shown in the figure…
Theory of Machines · 3
- Q17 · 1 markA gear train with five gears is shown in the figure below. The number of teeth on each gear is N1, N2, N3, N4, and N5.…
- Q20 · 1 markThe rotor of an aeroplane engine has a mass moment of inertia 1.0 kg m2. The engine rotates at a speed of 500 RPM in…
- Q22 · 1 markWorm gearsets are used for transmitting rotary motion between
Vibrations · 2
Machine Design · 2
Thermodynamics · 6
- Q23 · 1 markFor an ideal gas, starting from state point 1, two different processes take place. The corresponding final states in…
- Q28 · 1 markFor the isothermal expansion of an ideal gas in a piston cylinder system, the net heat supplied during the process is…
- Q44 · 2 marksFor an ideal regenerative Rankine cycle, as shown in the figure below, which one of the following options is the…
- Q56 · 2 marksA liquid comes out of the reactor of a chemical plant at 250 circC temperature with a flow rate of 100 LPM. The…
- Q57 · 2 marksA rigid closed vertical cylindrical vessel of 15 cm diameter contains 5 kg water at 80 circC with 10% quality. The…
- Q58 · 2 marksAn inward flow reaction turbine, having an outer diameter of 1 m, runs at 600 RPM. The normal component of absolute…
Fluid Mechanics · 5
- Q24 · 1 markA steady incompressible laminar flow passes through a 90° tube bend placed on a horizontal surface. In horizontal…
- Q25 · 1 markAn ideal gas passes isothermally through a long horizontal uniform cross-section pipe under steady flow. Consider that…
- Q26 · 1 markBernoulli's equation CANNOT be applied between
- Q29 · 1 markA hydraulic crane supports a mass of 500 kg with its piston-cylinder actuator, inclined at 60° with horizontal, as…
- Q53 · 2 marksWater with a density of 1000 kg/m3 comes out of an industrial condenser through a horizontal pipe of 15 cm radius at…
Heat Transfer · 5
- Q27 · 1 markA quiescent fluid at temperature T3 is confined between two vertical parallel plates. While plate 1 is kept at…
- Q35 · 1 markA sphere of radius 5 mm is initially in equilibrium at 400 °C in a furnace. It is suddenly removed from the furnace…
- Q43 · 2 marksA very long fin of a uniform square cross-section is replaced by another very long fin of a uniform circular…
- Q54 · 2 marksTwo rectangular surfaces both having 1 m2 area are placed perpendicular to each other with a common edge. One surface…
- Q55 · 2 marksConvective heat transfer coefficients for Fluid 1 and Fluid 2 in a heat exchanger, as shown in the figure below, are…
Manufacturing Engineering · 9
- Q30 · 1 markIn relation to metal casting defects, match the following | Defect | | Description | | | :--- | :--- | :--- | :--- | |…
- Q31 · 1 markWhich one of the following options is NOT an error associated with STereoLithography (STL) file in additive…
- Q32 · 1 markA work piece is to be firmly held in a fixture. It is to be machined by using a plain slab milling cutter as shown in…
- Q33 · 1 markA two-dimensional surface profile is obtained over a sampling length by using a contact type stylus profilometer as…
- Q45 · 2 marksConsider the Euler variables of polyhedral objects namely, P1, P2, P3, and P4 as given in the table below. |…
- Q59 · 2 marksIn a deep drawing operation of a rectangular sheet metal, 30% stretching in length results in 15% reduction in…
- Q62 · 2 marksA metal has FCC crystal structure with 2.71 g/cm3 of density and 26.98 g/mol of atomic weight. The Avogadro's number…
- Q63 · 2 marksDuring orthogonal turning by using a single point cutting tool, feed rate is 0.24 mm/rev. The uncut chip thickness is…
- Q64 · 2 marksA drill bit during its lifetime can produce 150 through holes in a plate at a drill-speed of 200 RPM. If the…
Mechanics of Materials · 5
- Q34 · 1 markA steel plate having yield strength of 550 MPa, is subjected to biaxial state of stress as σx = σ and σy = -2σ. Using…
- Q40 · 2 marksA cantilever beam of length L is subjected to a concentrated load P and a moment M as shown in the figure below.…
- Q49 · 2 marksA simply supported beam is subjected to an external point load P as shown in the figure below. The beam has a…
- Q51 · 2 marksA cylindrical pressure vessel made of steel has diameter of 3 m and wall thickness of 15 mm. For steel, Young's…
- Q52 · 2 marksA welded square plate of 1 m × 1 m is subjected to biaxial stress of magnitude 6.5 MPa and 25 MPa, as shown in the…
Industrial Engineering · 5
- Q46 · 2 marksAn objective function Z of primal variables (x1 and x2) is described below: Minimize Z = 0.07 x1 + 0.05 x2 subject to…
- Q47 · 2 marksFour jobs are on order in a factory. As on day 20 of the production calendar, the corresponding due date and work…
- Q60 · 2 marksThe actual demand for castings in a factory is 500 units and 635 units for the months of January 2026 and February…
- Q61 · 2 marksThe inventory holding cost of an item is ₹ 0.50 per unit per month and the ordering cost per order is ₹ 550. A…
- Q65 · 2 marksThe activities of a PERT network and their corresponding activity time estimates (in weeks) i.e., optimistic (to),…
Sit this paper as the real exam
Three hours on the GATE exam screen, with the virtual calculator, then your marks and every solution.
Take it as a mock