GATE 2018 ME Set 1 question paper with solutions
All 65 questions of the official GATE 2018 · Mechanical Engineering · Set 1 · IIT Guwahati paper, each with the official answer and a worked solution.
Questions
General Aptitude · 10
- Q1 · 1 mark“Going by the ________ that many hands make light work, the school ________ involved all the students in the task.”…
- Q2 · 1 mark“Her ________ should not be confused with miserliness; she is ever willing to assist those in need.” The word that…
- Q3 · 1 markSeven machines take 7 minutes to make 7 identical toys. At the same rate, how many minutes would it take for 100…
- Q4 · 1 markA rectangle becomes a square when its length and breadth are reduced by 10 m and 5 m, respectively. During this…
- Q5 · 1 markA number consists of two digits. The sum of the digits is 9. If 45 is subtracted from the number, its digits are…
- Q6 · 2 marksFor integers a, b and c, what would be the minimum and maximum values respectively of a + b + c if |a| + |b| + |c| = 0?
- Q7 · 2 marksGiven that a and b are integers and a + a2 b3 is odd, which one of the following statements is correct?
- Q8 · 2 marksFrom the time the front of a train enters a platform, it takes 25 seconds for the back of the train to leave the…
- Q9 · 2 marksWhich of the following functions describe the graph shown in the below figure?
- Q10 · 2 marksConsider the following three statements: (i) Some roses are red. (ii) All red flowers fade quickly. (iii) Some roses…
Engineering Mathematics · 10
- Q11 · 1 markFour red balls, four green balls and four blue balls are put in a box. Three balls are pulled out of the box at random…
- Q12 · 1 markThe rank of the matrix bmatrix -4 1 -1 -1 -1 -1 7 -3 1 bmatrix is
- Q13 · 1 markAccording to the Mean Value Theorem, for a continuous function f(x) in the interval [a, b], there exists a value in…
- Q14 · 1 markF(z) is a function of the complex variable z = x + iy given by F(z) = i z + k Re(z) + i Im(z). For what value of k…
- Q28 · 1 markA six-faced fair dice is rolled five times. The probability (in %) of obtaining "ONE" at least four times is
- Q36 · 2 marksLet X1, X2 be two independent normal random variables with means μ1, μ2 and standard deviations σ1, σ2, respectively.…
- Q37 · 2 marksThe value of the integral S r × n dS over the closed surface S bounding a volume V, where r = x i + y j + z k is the…
- Q47 · 2 marksAn explicit forward Euler method is used to numerically integrate the differential equation dy/dt = y using a time…
- Q48 · 2 marksF(s) is the Laplace transform of the function f(t) = 2t2 e-t F(1) is _______ (correct to two decimal places).
- Q61 · 2 marksThe minimum value of 3x + 5y such that: 3x + 5y ≤ 15 4x + 9y ≤ 8 13x + 2y ≤ 2 x ≥ 0, y ≥ 0 is _______.
Engineering Mechanics · 3
- Q15 · 1 markA bar of uniform cross section and weighing 100 N is held horizontally using two massless and inextensible strings S1…
- Q38 · 2 marksA point mass is shot vertically up from ground level with a velocity of 4 m/s at time, t = 0. It loses 20% of its…
- Q64 · 2 marksBlock P of mass 2 kg slides down the surface and has a speed 20 m/s at the lowest point, Q, where the local radius of…
Mechanics of Materials · 8
- Q16 · 1 markIf σ1 and σ3 are the algebraically largest and smallest principal stresses respectively, the value of the maximum…
- Q21 · 1 markIn a linearly hardening plastic material, the true stress beyond initial yielding
- Q29 · 1 markA steel column of rectangular section (15 mm × 10 mm) and length 1.5 m is simply supported at both ends. Assuming…
- Q39 · 2 marksThe state of stress at a point, for a body in plane stress, is shown in the figure below. If the minimum principal…
- Q41 · 2 marksA carpenter glues a pair of cylindrical wooden logs by bonding their end faces at an angle of θ = 30° as shown in the…
- Q49 · 2 marksA simply supported beam of width 100 mm, height 200 mm and length 4 m is carrying a uniformly distributed load of…
- Q58 · 2 marksThe true stress (σ) - true strain ( ) diagram of a strain hardening material is shown in figure. First, there is…
- Q60 · 2 marksA bar is compressed to half of its original length. The magnitude of true strain produced in the deformed bar is…
Vibrations · 2
Theory of Machines · 5
- Q18 · 1 markFor an Oldham coupling used between two shafts, which among the following statements are correct? I. Torsional load is…
- Q30 · 1 markA four bar mechanism is made up of links of length 100, 200, 300 and 350 mm. If the 350 mm link is fixed, the number…
- Q40 · 2 marksAn epicyclic gear train is shown in the figure below. The number of teeth on the gears A, B and D are 20, 30 and 20,…
- Q51 · 2 marksA slider crank mechanism is shown in the figure. At some instant, the crank angle is 45° and a force of 40 N is acting…
- Q63 · 2 marksThe schematic of an external drum rotating clockwise engaging with a short shoe is shown in the figure. The shoe is…
Fluid Mechanics · 6
- Q19 · 1 markFor a two-dimensional incompressible flow field given by u = A(x i - y j), where A > 0, which one of the following…
- Q32 · 1 markA flat plate of width L = 1 m is pushed down with a velocity U = 0.01 m/s towards a wall resulting in the drainage of…
- Q43 · 2 marksA tank open at the top with a water level of 1 m, as shown in the figure, has a hole at a height of 0.5 m. A free jet…
- Q44 · 2 marksIn a Lagrangian system, the position of a fluid particle in a flow is described as x = xo e-kt and y = yo ekt where t…
- Q52 · 2 marksA sprinkler shown in the figure rotates about its hinge point in a horizontal plane due to water flow discharged…
- Q53 · 2 marksA solid block of 2.0 kg mass slides steadily at a velocity V along a vertical wall as shown in the figure below. A…
Thermodynamics · 6
- Q20 · 1 markWhich one of the following statements is correct for a superheated vapour?
- Q33 · 1 markAn ideal gas undergoes a process from state 1 (T1 = 300 K, p1 = 100 kPa) to state 2 (T2 = 600 K, p2 = 500 kPa). The…
- Q34 · 1 markFor a Pelton wheel with a given water jet velocity, the maximum output power from the Pelton wheel is obtained when…
- Q54 · 2 marksA tank of volume 0.05 m3 contains a mixture of saturated water and saturated steam at 200°C. The mass of the liquid…
- Q55 · 2 marksSteam flows through a nozzle at a mass flow rate of m = 0.1 kg/s with a heat loss of 5 kW. The enthalpies at inlet and…
- Q56 · 2 marksAn engine working on air standard Otto cycle is supplied with air at 0.1 MPa and 35°C. The compression ratio is 8. The…
Manufacturing Engineering · 10
- Q22 · 1 markThe type of weld represented by the shaded region in the figure is
- Q23 · 1 markUsing the Taylor's tool life equation with exponent n = 0.5, if the cutting speed is reduced by 50%, the ratio of new…
- Q24 · 1 markA grinding ratio of 200 implies that the
- Q25 · 1 markInterpolator in a CNC machine
- Q27 · 1 markThe number of atoms per unit cell and the number of slip systems, respectively, for a face-centered cubic (FCC)…
- Q35 · 1 markThe height (in mm) for a 125 mm sine bar to measure a taper of 27° 32' on a flat work piece is ________ (correct to…
- Q45 · 2 marksThe maximum reduction in cross-sectional area per pass (R) of a cold wire drawing process is R = 1 - e-(n+1), where n…
- Q46 · 2 marksThe percentage scrap in a sheet metal blanking operation of a continuous strip of sheet metal as shown in the figure…
- Q59 · 2 marksAn orthogonal cutting operation is being carried out in which uncut thickness is 0.010 mm, cutting speed is 130 m/min,…
- Q65 · 2 marksAn electrochemical machining (ECM) is to be used to cut a through hole into a 12 mm thick aluminum plate. The hole has…
Industrial Engineering · 2
Machine Design · 2
Heat Transfer · 1
Sit this paper as the real exam
Three hours on the GATE exam screen, with the virtual calculator, then your marks and every solution.
Take it as a mock