GATE 2012 ME question paper with solutions
All 65 questions of the official GATE 2012 · Mechanical Engineering · IIT Delhi paper, each with the answer and a worked solution.
Questions
Manufacturing Engineering · 11
- Q1 · 1 markIn abrasive jet machining, as the distance between the nozzle tip and the work surface increases, the material removal…
- Q2 · 1 markMatch the following metal forming processes with their associated stresses in the workpiece. | Metal forming process |…
- Q3 · 1 markIn an interchangeable assembly, shafts of size 25.000-0.010+0.040 mm mate with holes of size 25.000+0.020+0.030 mm.…
- Q4 · 1 markDuring *normalizing* process of steel, the specimen is heated
- Q15 · 1 markA CNC vertical milling machine has to cut a straight slot of 10 mm width and 2 mm depth by a cutter of 10 mm diameter…
- Q16 · 1 markA solid cylinder of diameter 100 mm and height 50 mm is forged between two frictionless flat dies to a height of 25…
- Q27 · 2 marksDetails pertaining to an orthogonal metal cutting process are given below. | | | |---|---| | Chip thickness ratio |…
- Q28 · 2 marksIn a single pass drilling operation, a through hole of 15 mm diameter is to be drilled in a steel plate of 50 mm…
- Q37 · 2 marksCalculate the punch size in mm, for a circular blanking operation for which details are given below. | Size of the…
- Q38 · 2 marksIn a single pass rolling process using 410 mm diameter steel rollers, a strip of width 140 mm and thickness 8 mm…
- Q39 · 2 marksIn a DC arc welding operation, the voltage-arc length characteristic was obtained as Varc = 20 + 5l where the arc…
Fluid Mechanics · 3
- Q5 · 1 markOil flows through a 200 mm diameter horizontal cast iron pipe (friction factor, f = 0.0225) of length 500 m. The…
- Q30 · 2 marksAn incompressible fluid flows over a flat plate with zero pressure gradient. The boundary layer thickness is 1 mm at a…
- Q40 · 2 marksA large tank with a nozzle attached contains three immiscible, inviscid fluids as shown. Assuming that the changes in…
Heat Transfer · 4
- Q6 · 1 markFor an opaque surface, the absorptivity (α), transmissivity (τ) and reflectivity (ρ) are related by the equation:
- Q18 · 1 markWhich one of the following configurations has the highest fin effectiveness?
- Q29 · 2 marksConsider two infinitely long *thin* concentric tubes of circular cross section as shown in the figure. If D1 and D2…
- Q41 · 2 marksWater (Cp = 4.18 kJ/kg.K) at 80°C enters a counterflow heat exchanger with a mass flow rate of 0.5 kg/s. Air (Cp = 1…
Thermodynamics · 8
- Q7 · 1 markSteam enters an adiabatic turbine operating at steady state with an enthalpy of 3251.0 kJ/kg and leaves as a saturated…
- Q17 · 1 markThe velocity triangles at the inlet and exit of the rotor of a turbomachine are shown. V denotes the absolute velocity…
- Q19 · 1 markAn ideal gas of mass m and temperature T1 undergoes a reversible isothermal process from an initial pressure P1 to…
- Q31 · 2 marksA room contains 35 kg of dry air and 0.5 kg of water vapor. The total pressure and temperature of air in the room are…
- Q50 · 2 marksCommon Data for Questions 50 and 51: A refrigerator operates between 120 kPa and 800 kPa in an ideal vapor compression…
- Q51 · 2 marksCommon Data for Questions 50 and 51: A refrigerator operates between 120 kPa and 800 kPa in an ideal vapor compression…
- Q52 · 2 marksStatement for Linked Answer Questions 52 and 53: Air enters an adiabatic nozzle at 300 kPa, 500 K with a velocity of…
- Q53 · 2 marksStatement for Linked Answer Questions 52 and 53: Air enters an adiabatic nozzle at 300 kPa, 500 K with a velocity of…
Theory of Machines · 3
- Q8 · 1 markThe following are the data for two crossed helical gears used for speed reduction: Gear I : Pitch circle diameter in…
- Q20 · 1 markIn the mechanism given below, if the angular velocity of the eccentric circular disc is 1 rad/s, the angular velocity…
- Q21 · 1 markA circular solid disc of uniform thickness 20 mm, radius 200 mm and mass 20 kg, is used as a flywheel. If it rotates…
Engineering Mechanics · 3
- Q9 · 1 markA solid disc of radius r rolls without slipping on a horizontal floor with angular velocity ω and angular acceleration…
- Q48 · 2 marksCommon Data for Questions 48 and 49: Two steel truss members, AC and BC, each having cross sectional area of 100 mm2,…
- Q49 · 2 marksCommon Data for Questions 48 and 49: Two steel truss members, AC and BC, each having cross sectional area of 100 mm2,…
Mechanics of Materials · 6
- Q10 · 1 markA thin walled spherical shell is subjected to an internal pressure. If the radius of the shell is increased by 1% and…
- Q22 · 1 markA cantilever beam of length L is subjected to a moment M at the free end. The moment of inertia of the beam cross…
- Q23 · 1 markFor a long slender column of uniform cross section, the ratio of critical buckling load for the case with both ends…
- Q26 · 2 marksThe homogeneous state of stress for a metal part undergoing plastic deformation is T = pmatrix 10 5 0 5 20 0 0 0 -10…
- Q34 · 2 marksThe state of stress at a point under plane stress condition is σxx = 40 MPa, σyy = 100 MPa and τxy = 40 MPa. The…
- Q42 · 2 marksA solid steel cube constrained on all six faces is heated so that the temperature rises uniformly by Δ T. If the…
Engineering Mathematics · 10
- Q11 · 1 markThe area enclosed between the straight line y = x and the parabola y = x2 in the x-y plane is
- Q12 · 1 markConsider the function f(x) = |x| in the interval -1 ≤ x ≤ 1. At the point x = 0, f(x) is
- Q14 · 1 markx 0 ( 1 - x/x2 ) is
- Q24 · 1 markAt x = 0, the function f(x) = x3 + 1 has
- Q25 · 1 markFor the spherical surface x2 + y2 + z2 = 1, the unit outward normal vector at the point (1/ 2, 1/ 2, 0 ) is given by
- Q35 · 2 marksThe inverse Laplace transform of the function F(s) = 1/s(s+1) is given by
- Q36 · 2 marksFor the matrix A = bmatrix 5 3 1 3 bmatrix, ONE of the normalized eigen vectors is given as
- Q45 · 2 marksA box contains 4 red balls and 6 black balls. Three balls are selected randomly from the box one after another,…
- Q46 · 2 marksConsider the differential equation x2 d2 y/dx2 + x dy/dx - 4y = 0 with the boundary conditions of y(0) = 0 and y(1) =…
- Q47 · 2 marksaligned x + 2y + z = 4 2x + y + 2z = 5 x - y + z = 1 aligned The system of algebraic equations given above has
Industrial Engineering · 3
- Q13 · 1 markWhich one of the following is NOT a decision taken during the aggregate production planning stage?
- Q54 · 2 marksStatement for Linked Answer Questions 54 and 55: For a particular project, eight activities are to be carried out.…
- Q55 · 2 marksStatement for Linked Answer Questions 54 and 55: For a particular project, eight activities are to be carried out.…
Machine Design · 3
- Q32 · 2 marksA fillet welded joint is subjected to transverse loading F as shown in the figure. Both legs of the fillets are of 10…
- Q43 · 2 marksA solid circular shaft needs to be designed to transmit a torque of 50 N.m. If the allowable shear stress of the…
- Q44 · 2 marksA force of 400 N is applied to the brake drum of 0.5 m diameter in a band-brake system as shown in the figure, where…
Vibrations · 1
General Aptitude · 10
- Q56 · 1 markChoose the most appropriate alternative from the options given below to complete the following sentence: Suresh's dog…
- Q57 · 1 markThe cost function for a product in a firm is given by 5q2, where q is the amount of production. The firm can sell the…
- Q58 · 1 markChoose the most appropriate alternative from the options given below to complete the following sentence: Despite…
- Q59 · 1 markWhich one of the following options is the closest in meaning to the word given below? Mitigate
- Q60 · 1 markChoose the grammatically INCORRECT sentence:
- Q61 · 2 marksGiven the sequence of terms, AD CG FK JP, the next term is
- Q62 · 2 marksWanted Temporary, Part-time persons for the post of Field Interviewer to conduct personal interviews to collect and…
- Q63 · 2 marksA political party orders an arch for the entrance to the ground in which the annual convention is being held. The…
- Q64 · 2 marksAn automobile plant contracted to buy shock absorbers from two suppliers X and Y. X supplies 60% and Y supplies 40% of…
- Q65 · 2 marksWhich of the following assertions are CORRECT? P: Adding 7 to each entry in a list adds 7 to the mean of the list Q:…
Sit this paper as the real exam
Three hours on the GATE exam screen, with the virtual calculator, then your marks and every solution.
Take it as a mock