Materials, Casting, Forming and Joining: GATE ME previous year questions
129 questions from the official GATE Mechanical Engineering papers, chapter by chapter, newest first, each with its answer and a worked solution.
Chapters
Crystal Structure and Defects6 questionsPhase Diagrams and Heat Treatment19 questionsMechanical Properties, Plastic Deformation and Yield Criteria4 questionsCasting: Patterns, Moulds, Gating and Solidification34 questionsBulk Deformation I: Forging and Rolling18 questionsBulk Deformation II: Extrusion, Wire Drawing and Powder Metallurgy10 questionsSheet Metal Forming Processes9 questionsWelding I: Physics, Power Sources and Arc Welding18 questionsWelding II: Resistance Welding, Solid-State Joining and Allied Processes11 questions
1. Crystal Structure and Defects
- GATE 2026 ME · Q62A metal has FCC crystal structure with 2.71 g/cm3 of density and 26.98 g/mol of atomic weight. The…
- GATE 2023 ME · Q51The atomic radius of a hypothetical face-centered cubic (FCC) metal is ( 2/10) nm. The atomic weight of the…
- GATE 2020 ME Set 1 · Q20The crystal structure of γ iron (austenite phase) is
- GATE 2018 ME Set 1 · Q27The number of atoms per unit cell and the number of slip systems, respectively, for a face-centered cubic…
- GATE 2017 ME Set 2 · Q21The crystal structure of aluminium is
- GATE 2015 ME Set 2 · Q30The atomic packing factor for a material with body centered cubic structure is ________
2. Phase Diagrams and Heat Treatment
- GATE 2025 ME · Q20Among the following surface hardening processes, steel is heated to the lowest temperature in
- GATE 2024 ME · Q28The phases present in pearlite are
- GATE 2023 ME · Q52A steel sample with 1.5 wt.% carbon (no other alloying elements present) is slowly cooled from 1100 °C to…
- GATE 2022 ME Set 1 · Q27Which of the following heat treatment processes is/are used for surface hardening of steels?
- GATE 2022 ME Set 1 · Q41In Fe-Fe3C phase diagram, the eutectoid composition is 0.8 weight % of carbon at 725 °C. The maximum…
- GATE 2022 ME Set 2 · Q19Fluidity of a molten alloy during sand casting depends on its solidification range. The phase diagram of a…
- GATE 2021 ME Set 2 · Q14The Cast Iron which possesses all the carbon in the combined form as cementite is known as
- GATE 2020 ME Set 1 · Q21Match the following. | Heat treatment process | Effect | | :--- | :--- | | P: Tempering | 1. Strengthening |…
- GATE 2020 ME Set 2 · Q21Which one of the following statements about a phase diagram is INCORRECT?
- GATE 2019 ME Set 2 · Q24Hardenability of steel is a measure of
- GATE 2019 ME Set 2 · Q44The binary phase diagram of metals P and Q is shown in the figure. An alloy X containing 60% P and 40% Q (by…
- GATE 2018 ME Set 2 · Q22Denoting L as liquid and M as solid in a phase-diagram with the subscripts representing different phases, a…
- GATE 2017 ME Set 2 · Q22Given the atomic weight of Fe is 56 and that of C is 12, the weight percentage of carbon in cementite (…
- GATE 2016 ME Set 1 · Q30The "Jominy test" is used to find
- GATE 2016 ME Set 2 · Q31In the phase diagram shown in the figure, four samples of the same composition are heated to temperatures…
- GATE 2016 ME Set 2 · Q58In a binary system of A and B, a liquid of 20% A (80% B) is coexisting with a solid of 70% A (30% B). For an…
- GATE 2014 ME Set 1 · Q34The process of reheating the martensitic steel to reduce its brittleness without any significant loss in its…
- GATE 2014 ME Set 4 · Q34Match the heat treatment processes (Group A) and their associated effects on properties (Group B) of medium…
- GATE 2012 ME · Q4During *normalizing* process of steel, the specimen is heated
3. Mechanical Properties, Plastic Deformation and Yield Criteria
- GATE 2023 ME · Q57Ignoring the small elastic region, the true stress (sigma) – true strain (varepsilon) variation of a…
- GATE 2019 ME Set 1 · Q44A plane-strain compression (forging) of a block is shown in the figure. The strain in the z-direction is…
- GATE 2015 ME Set 3 · Q15The strain hardening exponent n of stainless steel SS 304 with distinct yield and UTS values undergoing…
- GATE 2014 ME Set 1 · Q61A metal rod of initial length L0 is subjected to a drawing process. The length of the rod at any instant is…
4. Casting: Patterns, Moulds, Gating and Solidification
- GATE 2026 ME · Q30In relation to metal casting defects, match the following | Defect | | Description | | | :--- | :--- | :---…
- GATE 2025 ME · Q34A liquid metal is poured in a mold cavity of size 200 mm × 200 mm × 200 mm. The cooling is uniform in all…
- GATE 2025 ME · Q38Match the mold elements in the casting process with the most suitable function | Mold element | | Function |…
- GATE 2025 ME · Q62Two metal parts (a cylinder and a cube) of same volume are cast under identical conditions. The diameter of…
- GATE 2024 ME · Q31The allowance provided to a pattern for easy withdrawal from a sand mold is
- GATE 2024 ME · Q61Aluminium is casted in a cube-shaped mold having dimensions as 20 mm × 20 mm × 20 mm. Another mold of the…
- GATE 2023 ME · Q25In a metal casting process to manufacture parts, both patterns and moulds provide shape by dictating where…
- GATE 2022 ME Set 2 · Q27Consider sand casting of a cube of edge length a. A cylindrical riser is placed at the top of the casting.…
- GATE 2021 ME Set 1 · Q46A true centrifugal casting operation needs to be performed horizontally to make copper tube sections with…
- GATE 2021 ME Set 2 · Q47A cast product of a particular material has dimensions 75 mm × 125 mm × 20 mm. The total solidification time…
- GATE 2020 ME Set 2 · Q52A mould cavity of 1200 cm3 volume has to be filled through a sprue of 10 cm length feeding a horizontal…
- GATE 2019 ME Set 1 · Q23In a casting process, a vertical channel through which molten metal flows downward from pouring basin to…
- GATE 2019 ME Set 1 · Q47Match the following sand mold casting defects with their respective causes. | Defect | Cause | | :--- | :---…
- GATE 2019 ME Set 2 · Q25The fluidity of molten metal of cast alloys (without any addition of fluxes) increases with increase in
- GATE 2019 ME Set 2 · Q60The figure shows a pouring arrangement for casting of a metal block. Frictional losses are negligible. The…
- GATE 2018 ME Set 2 · Q23During solidification of a pure molten metal, the grains in the casting near the mould wall are
- GATE 2018 ME Set 2 · Q60For sand-casting a steel rectangular plate with dimensions 80 mm × 120 mm × 20 mm, a cylindrical riser has…
- GATE 2017 ME Set 1 · Q54A sprue in a sand mould has a top diameter of 20 mm and height of 200 mm. The velocity of the molten metal…
- GATE 2016 ME Set 1 · Q32The part of a gating system which regulates the rate of pouring of molten metal is
- GATE 2016 ME Set 1 · Q59Heat is removed from a molten metal of mass 2 kg at a constant rate of 10 kW till it is completely…
- GATE 2016 ME Set 1 · Q61A cylindrical job with diameter of 200 mm and height of 100 mm is to be cast using modulus method of riser…
- GATE 2016 ME Set 2 · Q59Gray cast iron blocks of size 100 mm × 50 mm × 10 mm with a central spherical cavity of diameter 4 mm are…
- GATE 2016 ME Set 3 · Q31Equal amounts of a liquid metal at the same temperature are poured into three moulds made of steel, copper…
- GATE 2015 ME Set 1 · Q46The solidification time of a casting is proportional to (V/A )2, where V is the volume of the casting and A…
- GATE 2015 ME Set 2 · Q58A cube and a sphere made of cast iron (each of volume 1000 cm3) were cast under identical conditions. The…
- GATE 2015 ME Set 3 · Q17In full mould (cavity-less) casting process, the pattern is made of
- GATE 2015 ME Set 3 · Q42Ratio of solidification time of a cylindrical casting (height = radius) to that of a cubic casting of side…
- GATE 2015 ME Set 3 · Q60The dimensions of a cylindrical side riser (height = diameter) for a 25 cm × 15 cm × 5 cm steel casting are…
- GATE 2014 ME Set 1 · Q65An aluminium alloy (density 2600 kg/m3) casting is to be produced. A cylindrical hole of 100 mm diameter and…
- GATE 2014 ME Set 3 · Q32Match the casting defects (Group A) with the probable causes (Group B): | Group A | Group B | | :--- | :---…
- GATE 2014 ME Set 3 · Q35The hot tearing in a metal casting is due to
- GATE 2014 ME Set 3 · Q62A cylindrical blind riser with diameter d and height h, is placed on the top of the mold cavity of a closed…
- GATE 2014 ME Set 4 · Q63A cylindrical riser of 6 cm diameter and 6 cm height has to be designed for a sand casting mould for…
- GATE 2013 ME · Q16A cube shaped casting solidifies in 5 min. The solidification time in min for a cube of the same material,…
5. Bulk Deformation I: Forging and Rolling
- GATE 2025 ME · Q41A plate of 30 mm thickness is fed through a rolling mill with two powered rolls. Each roll has a diameter of…
- GATE 2022 ME Set 1 · Q56A 4 mm thick aluminum sheet of width w = 100 mm is rolled in a two-roll mill of roll diameter 200 mm each.…
- GATE 2021 ME Set 1 · Q50A 200 mm wide plate having a thickness of 20 mm is fed through a rolling mill with two rolls. The radius of…
- GATE 2021 ME Set 2 · Q51The thickness, width and length of a metal slab are 50 mm, 250 mm and 3600 mm, respectively. A rolling…
- GATE 2020 ME Set 1 · Q42A strip of thickness 40 mm is to be rolled to a thickness of 20 mm using a two-high mill having rolls of…
- GATE 2020 ME Set 1 · Q56The thickness of a steel plate with material strength coefficient of 210 MPa, has to be reduced from 20 mm…
- GATE 2020 ME Set 2 · Q32A bolt head has to be made at the end of a rod of diameter d = 12 mm by localized forging (upsetting)…
- GATE 2019 ME Set 2 · Q62The thickness of a sheet is reduced by rolling (without any change in width) using 600 mm diameter rolls.…
- GATE 2017 ME Set 2 · Q52A strip of 120 mm width and 8 mm thickness is rolled between two 300 mm-diameter rolls to get a strip of 120…
- GATE 2016 ME Set 1 · Q62A 300 mm thick slab is being cold rolled using roll of 600 mm diameter. If the coefficient of friction is…
- GATE 2015 ME Set 1 · Q31Match the following products with preferred manufacturing processes: | Product | Process | | :--- | :--- | |…
- GATE 2015 ME Set 1 · Q47In a slab rolling operation, the maximum thickness reduction (Δ hmax) is given by Δ hmax = μ2 R, where R is…
- GATE 2015 ME Set 3 · Q41In a rolling operation using rolls of diameter 500 mm, if a 25 mm thick plate cannot be reduced to less than…
- GATE 2014 ME Set 2 · Q63A mild steel plate has to be rolled in one pass such that the final plate thickness is 2/3rd of the initial…
- GATE 2014 ME Set 4 · Q35In a rolling process, the maximum possible draft, defined as the difference between the initial and the…
- GATE 2013 ME · Q10In a rolling process, the state of stress of the material undergoing deformation is
- GATE 2012 ME · Q16A solid cylinder of diameter 100 mm and height 50 mm is forged between two frictionless flat dies to a…
- GATE 2012 ME · Q38In a single pass rolling process using 410 mm diameter steel rollers, a strip of width 140 mm and thickness…
6. Bulk Deformation II: Extrusion, Wire Drawing and Powder Metallurgy
- GATE 2025 ME · Q39Wire drawing operation is performed on a perfectly plastic metal without any strain hardening. Assuming no…
- GATE 2022 ME Set 2 · Q58A cylindrical billet of 100 mm diameter and 100 mm length is extruded by a direct extrusion process to…
- GATE 2021 ME Set 2 · Q15The size distribution of the powder particles used in Powder Metallurgy process can be determined by
- GATE 2018 ME Set 1 · Q45The maximum reduction in cross-sectional area per pass (R) of a cold wire drawing process is R = 1 -…
- GATE 2018 ME Set 2 · Q24Match the following products with the suitable manufacturing process | Product | Manufacturing Process | |…
- GATE 2018 ME Set 2 · Q57A steel wire is drawn from an initial diameter (di) of 10 mm to a final diameter (df) of 7.5 mm. The half…
- GATE 2017 ME Set 2 · Q25It is desired to make a product having T-shaped cross-section from a rectangular aluminium block. Which one…
- GATE 2015 ME Set 2 · Q59In a two-stage wire drawing operation, the fractional reduction (ratio of change in cross-sectional area to…
- GATE 2014 ME Set 2 · Q35With respect to metal working, match Group A with Group B: | Group A | Group B | | :--- | :--- | | P: Defect…
- GATE 2012 ME · Q2Match the following metal forming processes with their associated stresses in the workpiece. | Metal forming…
7. Sheet Metal Forming Processes
- GATE 2026 ME · Q59In a deep drawing operation of a rectangular sheet metal, 30% stretching in length results in 15% reduction…
- GATE 2024 ME · Q29The “Earing” phenomenon in metal forming is associated with
- GATE 2024 ME · Q62A blanking operation is performed on C20 steel sheet to obtain a circular disc having a diameter of 20 mm…
- GATE 2020 ME Set 1 · Q32A sheet metal with a stock hardness of 250 HRC has to be sheared using a punch and a die having a clearance…
- GATE 2018 ME Set 1 · Q46The percentage scrap in a sheet metal blanking operation of a continuous strip of sheet metal as shown in…
- GATE 2017 ME Set 1 · Q48A 10 mm deep cylindrical cup with diameter of 15 mm is drawn from a circular blank. Neglecting the variation…
- GATE 2016 ME Set 3 · Q60In a sheet metal of 2 mm thickness a hole of 10 mm diameter needs to be punched. The yield strength in…
- GATE 2014 ME Set 2 · Q65A rectangular hole of size 100 mm × 50 mm is to be made on a 5 mm thick sheet of steel having ultimate…
- GATE 2012 ME · Q37Calculate the punch size in mm, for a circular blanking operation for which details are given below. | Size…
8. Welding I: Physics, Power Sources and Arc Welding
- GATE 2025 ME · Q33During a welding operation, thermal power of 2500 W is incident normally on a metallic surface. As shown in…
- GATE 2024 ME · Q32The most suitable electrode material used for joining low alloy steels using Gas Metal Arc Welding (GMAW)…
- GATE 2024 ME · Q63In an arc welding process, the voltage and current are 30 V and 200 A, respectively. The cross-sectional…
- GATE 2022 ME Set 1 · Q57Two mild steel plates of similar thickness, in butt-joint configuration, are welded by gas tungsten arc…
- GATE 2022 ME Set 2 · Q57In a direct current arc welding process, the power source has an open circuit voltage of 100 V and short…
- GATE 2020 ME Set 2 · Q20Two plates, each of 6 mm thickness, are to be butt-welded. Consider the following processes and select the…
- GATE 2019 ME Set 2 · Q61A gas tungsten arc welding operation is performed using a current of 250 A and an arc voltage of 20 V at a…
- GATE 2018 ME Set 1 · Q22The type of weld represented by the shaded region in the figure is
- GATE 2018 ME Set 2 · Q63A welding operation is being performed with voltage = 30 V and current = 100 A. The cross-sectional area of…
- GATE 2017 ME Set 1 · Q23In an arc welding process, welding speed is doubled. Assuming all other process parameters to be constant,…
- GATE 2016 ME Set 2 · Q32The welding process which uses a blanket of fusible granular flux is
- GATE 2016 ME Set 2 · Q60The voltage-length characteristic of a direct current arc in an arc welding process is V = (100 + 40l),…
- GATE 2015 ME Set 1 · Q34In a linear arc welding process, the heat input per unit length is inversely proportional to
- GATE 2015 ME Set 1 · Q41A DC welding power source has a linear voltage-current (V-I) characteristic with open circuit voltage of 80…
- GATE 2015 ME Set 2 · Q61During a TIG welding process, the arc current and arc voltage were 50 A and 60 V, respectively, when the…
- GATE 2014 ME Set 1 · Q32The major difficulty during welding of aluminium is due to its
- GATE 2014 ME Set 4 · Q30Within the Heat Affected Zone (HAZ) in a fusion welding process, the work material undergoes
- GATE 2012 ME · Q39In a DC arc welding operation, the voltage-arc length characteristic was obtained as Varc = 20 + 5l where…
9. Welding II: Resistance Welding, Solid-State Joining and Allied Processes
- GATE 2025 ME · Q21The welding process commonly used for fabricating tailor-welded blanks of dissimilar thickness for…
- GATE 2023 ME · Q23Two surfaces P and Q are to be joined together. In which of the given joining operation(s), there is no…
- GATE 2021 ME Set 1 · Q47The resistance spot welding of two 1.55 mm thick metal sheets is performed using welding current of 10000 A…
- GATE 2021 ME Set 2 · Q48A spot welding operation performed on two pieces of steel yielded a nugget with a diameter of 5 mm and a…
- GATE 2019 ME Set 1 · Q24Which one of the following welding methods provides the highest heat flux (W/mm2)?
- GATE 2016 ME Set 1 · Q31Under optimal conditions of the process the temperatures experienced by a copper work piece in fusion…
- GATE 2016 ME Set 3 · Q58Spot welding of two steel sheets each 2 mm thick is carried out successfully by passing 4 kA of current for…
- GATE 2015 ME Set 3 · Q31Which two of the following joining processes are autogeneous? (i) Diffusion welding (ii) Electroslag welding…
- GATE 2014 ME Set 1 · Q35In solid-state welding, the contamination layers between the surfaces to be welded are removed by
- GATE 2014 ME Set 3 · Q65For spot welding of two steel sheets (base metal) each of 3 mm thickness, welding current of 10000 A is…
- GATE 2013 ME · Q11Match the CORRECT pairs. | Processes | Characteristics / Applications | | :--- | :--- | | P. Friction…